Turning the Bed

We've been making plans about what to restore and what we might modify with the Avion. In general we are thinking that we will restore the outside to preserve it's vintage appearance, but for the interior we are considering some changes to improve its function specific to how we think will use it. One major element we have been working on is turning the bed 90 degrees so either one us can get in and out without climbing over the other. The cab-over area on Avion C-10's & C-11's is pretty short which makes turning the bed fairly complicated. The folks over at RoamLab did an amazing job extending the cab-over of their C-11, but we are looking at a way to do this without modifying the structure.

I drew up a bunch concepts, then built a simple full-size cardboard mock-up of an approach that I think will work. The bed basically overhangs the dinette by about 24" and likely will need to be supported by two legs that can attach to the dinette seat base.  If I keep the bed length to around 75" (same as a Full size mattress) there is just enough room for two to sit at the un-covered portion of the dinette. When we want to use the full dinette, the 24" section of mattress lifts up and slides over the main mattress into the cab-over area, and the 24" support panel slides-in under the main section of mattress. Our thought is that when traveling and just stopping for one night we'd likely leave the bed "out", but when camping in one place for a while we would put the bed in if we wanted to hang-out inside the camper due to weather or whatever. This design also lets us keep the existing cab-over storage cabinet for clothes) and we can add another storage area of similar size on the opposite side while still having ample room around the bed. To ease getting in & out of the bed I'm thinking about a plank-style step thats supported by the dinette base. I've got a couple of ideas for how this plank step can stow away when not in use, and also some ideas for tricks with the dinette table that will help with all this come together. I'll have to get into actually building it to work out a bunch of details, but I am feeling good that this approach.

Winter Research

It's been pretty cold, so most of the work on the Avion has been pretty limited. I've definitely spent more hours digging around on the internet than any actual work on the camper.  One thing that we found worthwhile was an afternoon stomping around in the snow (and indoors) at a local RV Show to check out what's going on in the world of new RV's. While there's some pretty cool things happening with new campers of all sizes, this visit confirmed that "vintage" is still the right thing for us. Besides how much we've enjoyed spending time at TCT rallies with our Shasta, we just really like the old materials and aesthetics of campers from the 50's and 60's. The show also helped provide a reality check, as the price of new campers helped us realize that some of the components that we might want to purchase for the Avion are not so expensive after all. There were only a few Truck Campers at the show, but we did come back home with some ideas and good insights that will help a lot with the Avion.

Inside the Avion C-10 Truck Camper

What's inside of our Avion C10?
Overall it's in pretty good condition, especially compared to other 50 year old truck campers and maybe 50 year old campers of any type.  It's a Center Dinette model which doesn't seem to be as common as the Side Dinette layouts that seems to be in most of the Avion truck campers I see around the internet. All the original appliances are there except for the hot water heater and toilet which have been removed by a previous owner. The dinette table drops down and the seat cushions can be arranged to make a second bed. There is very little evidence of any water damage, just a little at one corner of the front window. The floor seems to be pretty solid except for a few inches that that will need attention just inside the door, and the wood door threshold itself will need to be replaced. Our first impression is that it has a lot of storage areas for its size, especially in the overhead cabinets and a wardrobe of sorts in the cab-over bed area.  There are also deeper storage areas under the dinette seats and a "compartment" that reminds me of the ones in the Millennium Falcon in the dinette floor that would be good place for a toolbox or heavy cast iron pans. The woodwork is not banged up but will need to be refinished, in a few few places some of the cabinet veneer will need some attention. The original speckled interior wall paint is intact but fairly dirty, once it's warm enough to work outside we will have to see how it cleans up to decide what happens with it.

Dealing with it!

Now that we had the Avion home, it took some time to deal with getting it off the trailer and into our garage for the winter. To get it off the trailer I used an electric boat trailer winch so that I could control it going down the equipment trailer's ramps. I also attached two conventional tongue jacks with castors to the front corners of the utility trailer, so that it would have four wheels.  While a little scary, this worked out well!

The next step was getting the Avion into the garage. I knew that the camper itself would clear our door, but apparently I am not so good with numbers. We ended up removing the rims from the utility trailer and tried to roll it in on the hubs, but this proved to have too much resistance. Eventually we ended up using a set of $4.- Magic Carpet Sliders under the hubs on carpet scraps while pulling with the electric winch which we now had attached to the Shasta which is deeper inside the garage. Yes our garage is pretty big, that's another story maybe for a future post.

Bringing the Avion C-10 Truck Camper Home

Retrieving the Avion took a bunch of planning. The camper was in the Canton Ohio area, about a 500 mile round trip from our home near Buffalo NY. While it seems like it would have been simple enough to just put it in a truck, I don't have a truck (yet). I also didn't feel comfortable borrowing one for this task, and didn't feel confident that it would be secure enough for travel not really knowing gate condition of the tie down points.

The Avion did come with a small utility trailer that its currently sitting on, however that trailer isn't quite up to the task of the length of the journey. My plan is to use the utility trailer as a dolly for the Avion while I work on it, it's made from an pop-up tent trailer and fits very well.

So to transport it I ended up renting an equipment trailer that worked out extremely well, having electric brakes, good tires, and a valid registration. I also took along good friend who has experience moving vintage vehicles, lots of ratchet straps, and took it slow. We ran into some minor lake effect snow on the way out, but the weather was fine on the way back.

A new project!

We are super excited to be at the beginning of another vintage camper project! The camper is an Avion C-10 truck camper. I think it's a 1965 model, but still need to do some work to confirm the year. I'll post some updates here once and a while as we learn more and start digging in!

Yes, still camping over 10 years later!

It's been a while since I've posted anything to the blog, but yes we are still camping in our Shasta. It's been over 10 years back on the road and we don't regret taking it on as project one bit. We don't get out as often as we'd like, but when we do it's usually in the woods and mountains are nice too!